New gut hook designs

I have been thinking yesterday about an easy-to-do knife pattern, where no handle is needed. Basically these are two sceleton knife designs.



I might put on a paracord wrap, or just leave it plain. I'll be making it from 3mm thick O-1 tool steel stock.
The hook of the second one needs some tweaking, I am not very happy with it's shape yet.

I'll start tomorrow with the smaller one, after creating a nice, evenly curved spine for it on the stock.

Cheers
5

Comments

Post a Comment

Popular posts from this blog

Glow in the dark GITD Micarta!?!?

Image
In the last few weeks I have been experimenting with some 15mm thick wood.  A beautyful, heavy, but very brittle, partially treated exotic hardwood, originally made for wooden floor. Won this GITD powder just today. Cant wait to have it in my hands. I dont know, if I mentioned it before, but this wood I have is hmmm... VERY brittle. Every and each time I try shaping it to a knife handle, it just cracks, and snaps. I have already ruined a 12x50cm board. So I got pretty much fed up with it by now. Some say I should steam it, to make it softer, but then I'm afraid, that the glue would not stick to it. I have this idea for a few weeks now, to make a GITD knife handle. But not the easy, "Buy a pair of Kirinite GITD knife scales!" way. I am rather thinking of making a canvas micarta, where I'd put some (A LOT:) glow in the dark (GITD) powder in the laminting resin. Today I won an auction of some -allegedly- powerful GITD powder, Id like to use for the process. Of...
Read this blogpost»

Ratot - my own design

Image
Hi there, havent been around for a while, have been psychologizing a lot, not leaving any time for my dear hobby. Since I managed to get away for a few hours only, I forgot to make enough pics. My bad, I'm sorry. But... here we go. A knife for a friend: In the last days of 2016, I have started a new knife, based on my own design. You may have seen it in this article. And now, in 2017 I have continued working on it. I guess we can say, im working on this knife for a year now :D:D The idea behind this knife was to make a  uncommon all-around knife. Since it is made from a 3mm thick material, it should take abuse (wood chopping/splitting, camping use, etc.) pretty easy. I know, lot of people in the US enjoy thicker blades, like 5mm+ (0.196 inches), but I believe, for a regular use, 3mm should be just fine. Blade material: O-1 tool steel  (1.2510 in the EU) 50mm wide, 3mm thick Heat treatment: My little gas forge Hardness: ~60 HRC (2x230 C cycles) Handle: Kirinit...
Read this blogpost»

Heat treat oven - electric

Image
Making my DIY heat treat kiln I started this build back in summer 2016 by buying all the necessary parts for the kiln: Close to finish Bill of materials: Heating element (wire coil, 80cm long, 5mm thick, rated 3.500W)  PID Controller: Rex C100 + 1.250C K-type thermocouple Solid State Relay (SSR, 25Amp) Aluminum heat sink for SSR Old PC fan and box 1.200C for the top, bottom and the door of the kiln, theese bricks will not touch the heating element 1.500C for the walls, theese will incorporate the heating wire Some angle iron (40x40x2mm) Door hinges  Basic layout of DIY heat treat kiln Basic layout I started assembling the core of the kiln. I used a Dremel 566 attachment to shape the groove, accomodating the heating element. I had to cut one thick brick in half, you can see it in the following picture, where one half of the cut piece is in the middle of the floor and the other in the roof ot the heat treating kiln. Bottom assembly of heat tre...
Read this blogpost»